The Greatest TV Wall Mount for 2020

The Sanus VMPL50A-B1 mounted on a wall
Photograph: Doug Mahoney

Our choose

In any case of our analysis and testing, we really feel the perfect tilting TV mount is the Sanus VMPL50A-B1. This UL-approved mount is designed for TVs ranging in measurement from 32 to 70 inches and might maintain as much as 130 kilos, which is greater than sufficient for any TV. The Sanus has among the many thinnest profiles of the examined mounts, holding the again of the TV about 1¾ inch off the wall. But, when tilted, there’s nonetheless room to get a hand behind the TV for wiring functions. Set up was fast and straightforward, and the mount is absolutely adjustable as soon as the TV is in place, each aspect to aspect (in case your studs aren’t in precisely the suitable place) and, with two bolts, to right the extent. The lean stress knobs, which set the tightness of the tilting motion, might be adjusted by hand, but when there’s not sufficient room, they will also be adjusted with the equipped hex wrench (that is more durable with bigger TVs). The VMPL50A-B1 is suitable with 22 VESA patterns and got here with 10 bolt sizes, the most important choice of any examined mount.

The VMPL50A-B1 can tilt 9 levels ahead and 10 levels again. This was just like the opposite examined mounts, most of which may tilt ahead and again wherever from 7 to 10 levels. Relying on the scale of the TV, this may give you a few additional inches of house to squeeze your hand in to plug in a brand new part. Some mounts provide slightly extra tilt than the VMPL50A-B1, however we don’t really feel {that a} diploma or two goes to make an enormous usability distinction. One factor we did like is that the VMPL50A has a pleasant vary of tilt up and down, and it may be adjusted with only one hand on the TV.

On the entire mounts, knobs on the monitor brackets management the stress of tilt; larger, heavier TVs want tighter stress and smaller, lighter TVs want much less. The VMPL50A-B1’s knobs are distinctive as a result of they’ll both be turned by hand or, in case your hand can’t match behind the TV, with the included hex wrench. With bigger TVs, making this adjustment might be tough even with the hex wrench (and most mounts have directions to set the lean tightening knobs earlier than mounting the TV to the wall plate).

A closeup on the adjustment knob in question, which is has a rectangular grip and a small hex bolt hole in the middle
The lean stress knobs of the VMPL50A-B1 might be adjusted by hand or with a hex wrench in case your hand can’t match. Photograph: Doug Mahoney

The identical hex key can be utilized to regulate the side-to-side stage of the TV as soon as it’s put in on the wall. The included hex key has a ball finish, which makes it simpler for the hex key to show the bolt whereas coming at it from an angle. The extent adjustment bolts are very near the wall, so this was a pleasant little contact.

As with nearly all of the mounts, set up was comparatively straightforward. The method is similar with all of them: First mount the wall plate to the wall with 4 bolts (all the time into studs or strong masonry), then connect the 2 mounting brackets to the again of the TV and, final, raise and set the TV so the brackets hold off the wall plate and lock them in. We appreciated that the VMPL50A-B1’s brackets lock in place with an audible click on. Getting the TV up and hooked on the wall plate is a clumsy maneuver, and it was a reduction figuring out when it was correctly secured. It’s additionally good that it locks in mechanically. On a number of the different fashions, the brackets should be secured with a tightening screw that’s slightly extra time-consuming.

A closeup on a sliding bolt
Every bracket on the VMPL50A-B1 has an adjustment bolt (prime) that fine-tunes the extent of the TV after it has been put in on the wall. Photograph: Doug Mahoney

The VMPL50A-B1 is suitable with 22 VESA patterns (the various bolt patterns discovered on the backs of TVs), and it comes with the most important bolt choice of the examined mounts. Most mounts include seven or eight different-size bolts, however solely the VMPL50A-B1 and the Rocketfish RF-TVMLPT03 include 10. This merely provides a larger likelihood at a profitable set up the primary time by with out having to name the producer to request bolts which might be suitable together with your TV.

The VMPL50A-B1 can mount right into a wooden stud or concrete block wall. Like nearly all of mounts, it isn’t for use with steel studs. All the acceptable {hardware} is included, which is one thing we are able to’t say about all of the mounts we tried. When you’re trying to place your mount on a brick wall, Sanus recommends hiring knowledgeable as a result of pure inconsistencies of brick.

The VMPL50A-B1 doesn’t include a mounting template to help with the drill gap placement. This actually didn’t make any distinction to us. The wall plate is gentle and straightforward sufficient to maneuver that we truly most popular straight utilizing that reasonably than the skinny, floppy cardboard templates that got here with a number of the different fashions.

Source link

Leave your vote

{{ reviewsOverall }} / 5 Users (0 votes)
Audience Quality0
Hookup Chance0
Privacy and Security0
What people say... Leave your rating
Order by:

Be the first to leave a review.

User AvatarUser Avatar
{{{ review.rating_title }}}
{{{review.rating_comment | nl2br}}}

This review has no replies yet.

Show more
Show more
{{ pageNumber+1 }}
Leave your rating

Your browser does not support images upload. Please choose a modern one



Leave a Reply

Your email address will not be published. Required fields are marked *

Log In

Forgot password?

Forgot password?

Enter your account data and we will send you a link to reset your password.

Your password reset link appears to be invalid or expired.

Log in

Privacy Policy

Add to Collection

No Collections

Here you'll find all collections you've created before.